Opinn hálf-vagn

Fliegl 3-Achs Plateausattel teleskopierbar

Chassis, semi-trailer, transport company
Fine-grained steel, welded lightweight construction, kingpin plate with replaceable 2" kingpin, main frame reinforcement for 25 tons, with center of gravity at 3 m loading length in the retracted state.
13 pairs of hooks for lashing straps, welded onto the cross members.
23 pairs of lashing eyes recessed in the outer frame, each rated at 3.5 tons.
24-ton, 2-speed support winch in reinforced design for loading and unloading, single-sided operation.
1 spare wheel holder for 1 spare wheel.
1 storage compartment for stowage, open, with the option of stowing items behind the front wall or in a compartment between the extended longitudinal beams!
4 pairs of stake pockets recessed in the outer frame for rectangular tubes 80x80 mm.
5 stake pockets recessed in the middle of the floor for rectangular tubes 80x80 mm, with reinforcing beam, installed between the outer stake pockets, except for one.
6 lashing/stake rails recessed across the floor over the entire width to the outer frame (max. usable internal width between the outer stake sockets approx. 2170 mm), approx. 100 mm high. With 20 mm round steel rails, top and bottom, spacing from top to bottom approx. 60 mm (of the round steel). Bottom with an angle plate as a closure, half open downwards. For lashing and inserting stakes 80 x 80 mm.
Pull-out ladder at the rear on the right side.
5 x 3 pairs of stake pockets recessed on the outside of the longitudinal beams for rectangular tubes 80x80 mm, including reinforcing beams.
10 "lightweight" stake sockets, B=80/ T=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded on at the bottom on both sides.
2 plastic toolboxes, b=600 / h=425 / t=460 mm, lockable.
Telescoping
extendable by a maximum of 4,000 mm and lockable approximately every 500 mm.
Main frame telescoping
Locking with pneumatic bolt locking + display of frame locking on both sides, operated via hand knob, operation for brake/locking and suspension on the left side in front of the axles.
Storage compartment between the longitudinal beams in the extended state.
Axles + Suspension
SAF disc brake axles with 430 mm disc diameter.
Last axle with trailing arm, with automatic reversing lock via reversing light and additional locking function on the vehicle via hand knob.
Axle spacing offset 1310/1410 mm.
Rsdpfx Ameza Dyyjueu
Air suspension.
1st axle automatic lift axle, also electrically operated from the truck, with start-up assistance.
Braking system
2-line compressed air braking system.
Spring brake parking brake.
2 non-interchangeable coupling heads at the front.
EBS Wabco, electronic braking system with EBS socket at the front.
With raising & lowering valve + auto-reset function.
Axle load recognition via EBS-CAN bus signal, for display on the display in the driver's cab, truck must be appropriately pre-equipped.
Wheels and tires
385/65 R 22.5" steel rims.
Electrical system
24 Volt, multi-chamber lights, yellow LED lighting on the side.
2 white position lights at the front in LED.
2 white/red side marker lights at the rear in LED.
2 x 7-pin and 1 x 15-pin non-interchangeable sockets at the front.
1 rotating beacon with bracket, switched via side light.
2 pairs of warning signs, LED illuminated and extendable to 3,500 mm.
Flashing side marker lights.
Side 7-pin sockets, positioning 2x front panel, 2x support legs, 2x rear end.
1 additional 7-pin socket, in the underrun protection at the rear.
2 additional LED work lights, top inside on the fron

Þessi auglýsing var sjálfvirkt þýdd. Villa í þýðingu gæti verið til staðar.