Lágur hleðslutæki

Fliegl DTS 300 P

Customized transport solution
Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements.

More information
Chassis
Steel welded construction
Turntable with heavy-duty ball bearing, storage box recessed in the turntable extension
Foldable rear support
2 support wedges with holder
Aluminum side impact protection
Splash guards at the rear over the entire width
Extendable widening sections to 3,000 mm (not in the rear slope)
Storage compartment for wooden planks in the center of the loading area
Wooden planks 70 mm for widening to 3000 mm
Tie-down eyes for low-bed trailers
3 pairs of tie-down points, each with 10 tons capacity, integrated in the floor at the front
6 pairs of tie-down recesses on the top and sides of the outer frame, each with 10 tons capacity
1 x near the gooseneck area
the rest distributed in between, with a distance of no more than 1200 mm
1 x rear slope
5 pairs of lashing pockets recessed in the outer frame, 70 x 40 mm inside, (convertible to 5-ton ring tie-down eyes, not included in the scope of supply)
Coupling device for trailer turntable
Drawbar with tested 40 mm drawbar eye
Axles + Suspension
SAF drum brake axles
Axle / chassis laser-aligned, reducing tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearing and mechanical
Axle load equalization (rocker equalization)
Braking system
2-line compressed air braking system
Color-coded line routing for easy servicing
Spring-loaded parking brake including
2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle,
ABS and ALB, with ABS plug at the front, with connection cable,
Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS!
Wheels and tires
235 / 75 R 17.5
at the manufacturer's choice
Steel rims in twin arrangement, factory silver
Electrical system
24 Volt, multi-chamber lights, yellow LED lighting on the side
2 white position lights at the front
2 white/red side marker lights at the rear
2 x 7-pin fail-safe plugs at the front, with connection cable,
1 LED rotating beacon with holder, switched via parking lights (beacon can be removed)
2 pairs of warning signs, double LED-illuminated and extendable to 3,000 mm
Floor
Front area with steel floor,
then with 70 mm softwood floor, in the wheel arch area steel / tread plate covering
Rear slope with 70 mm softwood floor
Low-bed platform including rear slope 8,200 mm
Ramps
Steel ramps 2800 mm long, 750 mm wide, laterally movable
covered with wood including
with spring-loaded support
Operating instructions
An exemption permit is required for a 10,000 kg axle load; only indivisible loads are possible!!!
The specified total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle / support and saddle loads.
Country of registration / signs
Country of registration: Germany
with Dekra approval and certificate (according to §13 EC - FGV)
24/7 service hotline
prepared for two-line license plate holder
Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear
Iodpfji Riy Esx Agfoaw
Paint finish
Frame DB 7350 Novagrau
10-year warranty against rust-through
Drawbar galvanized or black,
at the manufacturer's choice
Ramps hot-dip galvanized
Note: Archive images!

Customized transport solution
Configure your Flieg

Þessi auglýsing var sjálfvirkt þýdd. Villa í þýðingu gæti verið til staðar.