Einangrunarglerframleiðsluvéllisec
Inspection Lightwall
Einangrunarglerframleiðsluvél
lisec
Inspection Lightwall
framleiðsluár
2021
Ástand
Notað
Staðsetning
Maasmechelen 

Myndir sýna
Sýna kort
Upplýsingar um vélina
- Heiti vélar:
- Einangrunarglerframleiðsluvél
- framleiðandi:
- lisec
- Gerð:
- Inspection Lightwall
- framleiðsluár:
- 2021
- Ástand:
- mjög gott (notað)
Verð og staðsetning
- Staðsetning:
- Breitwaterstraat 22, 3630 Maasmechelen, BE
Hringdu
Vélasala

Hefur þú þegar auglýst notaða vélina þína?
Seldu í gegnum Machineseeker án þóknunar.
Meira um sölu á vélum
Meira um sölu á vélum
Tilboðsupplýsingar
- Auglýsingarauðkenni:
- A18625526
- uppfærsla:
- síðast þann 01.03.2025
Lýsing
1. Switch on the wall and the electronics.
Do this by switching on the mean switch and the lightwall (on the back). So switch on the multimeters. See photos 1 and 2
2. Adjust the upper and lower beam to the right cell height. Do this with 2 people. See photo 3
3. Check if there is no power on the cables coming from the power beam. Use the multimeters for this.
Godpfxov Ep U Aj Adkebu
4. Connect the cells with the cables.
5. Check the cells with the protocol “Q3 quality finished cell”.
6. Use the right voltages for the different products. 24V for ddLC and 46V for scatter.
7. When doing the capacity measurement, turn the black switching knob from “power” to “R/C”. When done turn it back to “power”
8. When you have ddLC cells use the lightwall and the rotatable polar.
9. If you have scatter cells remove the lightwall and use the spotlight. For swtiching on/of this spotlight you can use the remote control. See photo 4.
10. When you are done, please use the mainswitch to power down, and switch of the used lights.
Þessi auglýsing var sjálfvirkt þýdd. Villa í þýðingu gæti verið til staðar.
Do this by switching on the mean switch and the lightwall (on the back). So switch on the multimeters. See photos 1 and 2
2. Adjust the upper and lower beam to the right cell height. Do this with 2 people. See photo 3
3. Check if there is no power on the cables coming from the power beam. Use the multimeters for this.
Godpfxov Ep U Aj Adkebu
4. Connect the cells with the cables.
5. Check the cells with the protocol “Q3 quality finished cell”.
6. Use the right voltages for the different products. 24V for ddLC and 46V for scatter.
7. When doing the capacity measurement, turn the black switching knob from “power” to “R/C”. When done turn it back to “power”
8. When you have ddLC cells use the lightwall and the rotatable polar.
9. If you have scatter cells remove the lightwall and use the spotlight. For swtiching on/of this spotlight you can use the remote control. See photo 4.
10. When you are done, please use the mainswitch to power down, and switch of the used lights.
Þessi auglýsing var sjálfvirkt þýdd. Villa í þýðingu gæti verið til staðar.
Bjóðandi
Athugasemd: Skráðu þig ókeypis eða skráðu þig inn, til að fá aðgang að öllum upplýsingum.
Skráð frá: 2019
Senda fyrirspurn
Sími & Fax
+32 89 53... auglýsingar
Auglýsingunni þinni hefur verið eytt með góðum árangri
Villa kom upp